iss 1 c1u, date 13-7-2011 saw bandpass filter part no.: ACTF2137-140-SMP03 features ? for if saw filter ? ceramic package for s urface m ounted technology ( smt ) ? lead-free production and rohs compliance package dimensions top view, laser marking " nd?: manufacturer?s mark pin configuration 1 input ground 2 input 6 output ground 7 output 3,5,8,10 ground 4,9 case ground sign data (unit: mm) sign data (unit: mm) a 7.0 e 0.6 b 5.0 f 1.0 c 1.27 g 1.5 d 2.54 ?f ?: saw filter ?213 7 ?: part number ? ?: terminal 1 marking ??: lot number (the code shown below varies in a 4-year cycle) code 1 2 3 actf * 2137 4 5 6 7 8 9 10 11 12 2009 a b c d e f g h j k l m 2010 n p q r s t u v w x y z 2011 a b c d e f g h i j k m 2012 n p q r s t u v w x y z maximum ratings rating value unit source power p 15 dbm dc voltage v dc 0 v esd voltage (hb) v esd 800 v operating temperature range t a -40 ~ +85 c storage temperature range t stg -40 ~ +105 c
iss 1 c1u, date 13-7-2011 electrical characteristics reference temperature: t a = 25 c terminating source impedance: z s = 50 ? terminating load impedance: z l = 50 ? characteristic min. typ. max. unit center frequency f c ? 140.0 ? mhz insertion attenuation @ 140.0 mhz il ? 7.5 8.5 db pass bandwidth rel 1 db rel 20 db rel 30 db rel 45 db bw 1 bw 20 bw 30 bw 45 1.5 ? ? ? 1.57 4.68 5.22 5.67 4.7 mhz 5.25 6.4 ? 0.3 1 passband ripple (p-p) db group delay (@f c ) ? ? 0.82 us ultimate rejection 45 48 db temperature coefficient of frequency tc f ? 20 ? ppm/k rohs compliant electrostatic sensitive device test matching network l1=12nh l2=27nh l3=33nh (notes: component values may cha nge depending on board layout!)
iss 1 c1u, date 13-7-2011 typical frequency response pass band variation group delay phase ripple s11 smith chart s22 smith chart
iss 1 c1u, date 13-7-2011 stability characteristics test item condition of test 1 mechanical shock (a) drops: 3 times on concrete floor (b) height: 1.0 m (a) frequency of vibration: 10~55hz (b) amplitude: 1.5 mm 2 vibration resistance (c) directions: x,y and z (d) duration: 2 hours 3 moisture resistance (a) condition: 40c, 90~95% r.h. (b) duration: 96 hours (c) wait 4 hours before measurement 4 climatic sequence (a) +70c for 16 hours (b) +55c for 24 hours, 90~95% r.h. (c) -25c for 2 hours (d) +40c for 24 hours, 90~95% r.h. (e) wait 4 hours before measurement 5 high temperature exposure (a) temperature: 70c (b) duration: 250 hours (c) wait 4 hours before measurement 6 thermal impact (a) +70c for 30 minutes ? -25c for 30 minutes repeated 3 times (b) wait 4 hours before measurement requirements: the saw filer shall remain within the electrical specifications after tests. remarks ? saw devices should not be used in any type of fl uid such as water, oil, organic solvent, etc. ? be certain not to apply voltage exceeding the rated voltage of components. ? do not operate outside the recommended operating temperature range of components. ? sudden change of temperature shall be avoided, deter ioration of the characteristics can occur. ? be careful of soldering temperature and duration of components when soldering. ? do not place soldering iron on the body of components. ? be careful not to subject the terminals or leads of components to excessive force. ? saw devices are electrostatic se nsitive. please avoid static voltage during operation and storage. ? ultrasonic cleaning shall be avoided. ultrasonic vibration may c ause destruction of components. recommended soldering profile 1. the specifications of this device are subject to change or obsolescence without notice. 2. typically, equipment utilizing this device requires emissions testing and governm ent approval, which is the responsibility of the equipment manufacturer. 3. our liability is only assumed for the surface acoustic wa ve (saw) component(s) per se, not for applications, processes and circuits implemented within components or assemblies.
|
